Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateGenie Torsion Spring Replacement: The Boulder City Owner’s Guide
We replace Genie-compatible torsion springs in Boulder City, parts and labor included, and most jobs run $180 – $340 for a spring repair depending on the wire gauge and whether one or both springs are swapped. Same-day service is usually available because a failed spring is a car-stuck-in-the-garage emergency, and we treat it that way. You’ll know the problem before you call: the door slams down hard, or the opener hums and the heavy door barely lifts an inch off the floor.
Most owners here discover it on a hot afternoon. The door comes down with a bang that shakes the whole house, or the opener strains and gives up halfway. Either way, the spring above the door has let go, and the door is now dead weight.
Key Takeaways
- Genie-compatible torsion springs are matched by wire size, inside diameter, and length, not by opener brand.
- Installed spring repair in Boulder City runs $180 – $340, quoted in writing before we start.
- Any torsion spring under tension is dangerous to touch, so leave the winding bars alone.
- We service Genie, LiftMaster, and Chamberlain systems, and our technicians have up to 25 years of experience.
Which Genie Models This Applies To
Here’s the first thing to get straight: the torsion spring is part of the door, not the opener. A Genie opener, whether it’s a screw-drive 2562, a belt-drive 2128, or a chain-drive relay model, opens whatever door it’s paired with. So your Genie torsion spring replacement is really matched to the door’s weight and spring geometry, and the Genie name tells us which opener system we’ll need to reset afterward (limits, force settings, sometimes a new remote reprogram).
To identify the right part, we measure instead of guess. The label on the spring coil, or a careful caliper reading if the label is gone, gives us three numbers: the wire gauge, the inside diameter, and the wound length. Those three numbers are the actual spec, and they have to line up with the door’s weight. A 90-pound Boulder City door and a 150-pound door need very different springs.
On the OEM question: Genie-branded replacement springs are reliable, and a quality aftermarket spring from a reputable manufacturer is a perfectly sound swap when the specs match. We’ll tell you which we’re sourcing and why, and you’ll see the price before we touch a tool.
Styles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
Signs Your Genie Torsion Spring Replacement Is Failing
Torsion springs don’t usually wear gradually and quietly. They give you warnings, then they snap. Here’s what we see, and what each symptom actually means:
- The door comes down hard and there’s a loud bang. That’s a snap, not a slip. Both springs on a two-spring door often go within months of each other, so we measure the surviving one before we call the job done.
- The opener strains, hums, and the door barely lifts. The spring is doing less of the lifting work, so the opener is carrying weight it was never built to carry. Left alone, this is how openers get burned out.
- The door lifts a foot and stops, or reverses back down. A weak or broken spring changes the balance, and the opener’s force sensor trips on the extra load.
- A visible gap in the coil, or a spring hanging loose on one side. The coil has unwound or broken. That’s your confirmation the spring failed rather than the opener.
- You can lift the door by hand too easily, or not at all. A properly balanced door should hold roughly mid-way on its own. If it drops or fights you, the spring is off.
One Boulder City reality worth knowing: our summer heat and dry air work the springs harder than a mild climate would, and the seasonal swing from cool mornings to 100-degree afternoons adds to the metal fatigue. Springs here often fail on the first hot day after a cold snap, and that’s exactly when we get the calls.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s the number to plan around: most Genie torsion spring replacements in Boulder City land in the $180 – $340 range for a spring repair, parts and labor together. The low end is a single spring on a lighter door. The high end is a heavier door, a two-spring swap, or a high-cycle spring built to last longer.
What moves the range, plainly:
- One spring or two. If one spring broke, we check whether the second is close behind it, because a matched pair fails as a pair.
- Spring type. A standard spring versus a high-cycle spring (rated for more open-close cycles) costs more, but lasts longer.
- Door weight and gauge. Heavier doors need heavier wire, which costs more.
- What we find once we’re in there. Cables, drums, and bearings are checked at the same time, and if one of those is also worn, we’ll tell you before doing anything.
You get a written price before any work starts, and the number on the invoice matches the number we quoted. If the repair fails inside the guarantee period, our 365-Day Done Right Promise means we come back and fix it at no charge, and that’s in writing, not just said at the door.
DIY or Call Us?
There’s a safe half and a dangerous half here, and you should know which is which. Safely, an owner can look at the spring and note whether the coil has a visible gap or is hanging loose. You can too check the door’s balance by raising it halfway by hand and seeing if it holds, with the opener disconnected (pull the red release cord). And you can read the label on the coil to see the spring specs. That’s it.
What you shouldn’t do: put a winding bar to a torsion spring. A loaded torsion spring holds serious stored energy, and one slip can break a wrist or worse. If your door has a failed spring, treat the door as dead weight and don’t force the opener. The honest answer is that this is not a job for the homeowner, and the safer path is to call us at (844) 560-4479.
FAQs
A standard torsion spring typically lasts somewhere in the range of 10,000 open-close cycles, and Boulder City’s heat and dry air can shorten that. A household that opens its door four times a day will see a spring last far longer than one that opens it a dozen times. High-cycle springs are available if you want more cycles between replacements, and we’ll quote both so you can decide.
No. A broken torsion spring can’t be repaired, only replaced. The coil has failed at the break point, and bending or welding it back would be unsafe and unreliable. What we can do is replace the spring with a properly matched part and check the cables, drums, and opener settings while we’re there, so the fix holds.
A straightforward single-spring swap usually takes well under an hour for a trained technician, and a two-spring swap or a heavier door takes longer. We book a real arrival window, not a vague “sometime today,” so you know when to expect us. If the tension or balance test shows something else needs attention, we’ll quote it before starting.
We match the spring by wire gauge, inside diameter, and wound length rather than by opener name, then source the part to those specs from a quality supplier. We’ll tell you whether it’s Genie-branded or a quality aftermarket equivalent, and the price reflects what’s actually going in the door. Bramwell is an independent service provider, not affiliated with Genie, so we source the right part rather than pushing one brand.
When a Genie torsion spring lets go, the door stays down until you get it fixed. Call us at (844) 560-4479 for a free estimate and a written price before any work starts. A live person answers any hour, any day, and we’ll tell you exactly what your repair needs and what it costs.
Written by the team at Bramwell Garage Door Repair Boulder City, serving Boulder City and nearby areas.