Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateStyles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
See the difference
Before
After
Before
After
Before
AfterTorsion vs extension springs: choose torsion unless your Boulder City garage has the low header that rules it out
Choose torsion springs unless your garage doesn’t have the headroom for them; on a Boulder City garage built during the dam years, that’s often the deciding factor. A standard torsion spring needs roughly 10 to 12 inches of clearance above the door to mount on its shaft, and plenty of Historic District garages have about 7. That’s the real answer to “which spring is better” on these streets, and it’s the one most comparison pages leave out. Call (844) 560-4479 and we’ll tell you which setup your garage actually takes.

What actually separates the two spring types
Both springs do the same job: they carry most of the door’s weight so a person (or an opener) can lift it. They just do it from different places.
Torsion springs
A torsion spring is the single heavy steel coil mounted on a shaft directly above the door opening. It twists as the door closes and unwinds to lift it. Because it sits centered over the door and delivers balanced torque across the whole width, it’s the setup we recommend for almost any modern door, especially 16-foot double doors.
Extension springs
Extension springs are a pair of coils that stretch along the horizontal tracks on each side of the door. They’re common on older and lighter doors, and they can fit garages where a torsion setup simply won’t. The catch: extension springs need a safety cable threaded through the middle of each coil. Without that cable, a snapped spring becomes a projectile, and with the tight geometry of a 1930s garage that’s a real hazard, not a theoretical one.
Why Boulder City’s garages make this more than a preference
Boulder City is one of the few American cities whose entire historic core was built by the federal government in the 1930s as a planned Boulder Dam construction town. Those garages were sized for 1930s sedans, not today’s SUVs. In the Historic District you’ll find 7-foot-wide single-car garages with low headers and stucco walls, often with original wood or early steel doors. A standard 16-foot door physically won’t fit, and neither will a standard torsion setup in some of them.
That federal origin also left a dense cluster of original single-car garages that need careful reinforcement rather than a builder-grade tract-home swap-out of the kind you’d see in neighboring Henderson. And because many of these doors still carry their original hardware, a look-alike replacement can land on the Historic District’s architectural review radar. Worth knowing before anyone starts pulling parts.
Then there’s the heat. Triple-digit summers and high-desert UV punish steel and wood alike. A spring rated for 10,000 cycles in a temperate climate may show stress earlier here, and June through August is when heat-stressed torsion springs snap most often. Windblown grit off the Lake Mead shoreline works on rollers and tracks at the same time. None of this changes the basic recommendation, but it does shorten the timeline on a tired spring.
Side-by-side: which spring fits which Boulder City garage
| Consideration | Torsion spring | Extension springs |
|---|---|---|
| Headroom needed | Roughly 10-12 inches above the door | Fits low-header garages where torsion won’t |
| Best fit | 1970s-1990s ranches with standard headroom and 16-foot double doors | Narrow, low-clearance Historic District garages |
| Weight handling | Balanced torque across the door width | Two springs share the load at the sides |
| Safety consideration | Single coil under high tension on a shaft | Requires a safety cable through each coil |
| Typical repair cost | $180-$340 | $180-$340 |
Spring repair in Boulder City runs $180-$340 including parts and labor whether we’re replacing one torsion spring or a pair of extension springs, so the two options are usually close on price. The decision comes down to what your garage can physically take.
How we work out which one you need
We don’t guess from the driveway. Here’s the order we run through on a first visit:
- Measure the header clearance above the door and the door’s actual width and weight.
- Check the existing hardware, including whether your extension springs have safety cables threaded through each coil.
- Write out a price for each option your garage can actually take, before touching anything.
- Hand you the written numbers so you can compare them side by side, on paper, with no timer running.
- Do the job and leave the site cleaner than we found it.
Our technicians carry both spring types on every appointment, so we’re not trying to sell you the one that happens to be in the truck. The choice is made by your header height and door weight, not by what’s easy for us.
A word on safety, and we mean this plainly: torsion springs and cables are under extreme tension, and a wrong move can break a wrist or worse. Extension springs without safety cables are worse still. We won’t walk you through a DIY spring replacement, and no one else should either. This is the one job on the door best left to a trained professional with the right winding bars and the experience to know how much tension a coil is holding. Our technicians have up to 25 years of experience with exactly this work.
Why homeowners call Bramwell
Bramwell Garage Door Repair Boulder City works under the Kingswell standard, which has been in place since 2001, and every job follows the same four promises: a written price before any work starts, a real arrival window, a clean job site, and a written guarantee. Each location is independently owned and operated and has agreed to hold to those standards.
What that means in practice for a spring repair:
- Written price first. You’ll see the number for each option before we touch the existing hardware, and the invoice matches what you heard.
- Real arrival window. We tell you when we’ll be there, and a live person answers the phone 24/7 if plans change.
- 365-Day Done Right Promise. If the covered repair fails within a year, we come back and fix it at no charge. That’s in writing, not just said at the door.
- Background-checked, uniformed technicians on every visit, so you know who’s in your driveway.
We service all major brands, including Clopay and Chamberlain, along with LiftMaster, Genie, Amarr, Wayne Dalton, Craftsman and Raynor. If you need parts beyond springs, our team handles garage door parts in Boulder City as well, and you can always start at our home page to see the full range of repairs.
What else commonly goes with a spring job
When the spring goes, other parts usually show their age at the same time. We check them while we’re there and quote anything extra in writing before we do it.
| Repair | Typical Boulder City range |
|---|---|
| Spring repair | $180-$340 |
| Cable repair | $130-$250 |
| Roller replacement | $110-$220 |
| Track realignment | $120-$240 |
| Opener repair | $120-$320 |
| Panel replacement | $250-$500 |
| Full garage door repair | $150-$600 |
If a panel or opener is involved, those are separate decisions from the spring, and we’ll tell you honestly when a repair makes more sense than a replacement.
FAQs
Choose torsion springs if your garage has 10-12 inches of clearance above the door, because the balanced torque handles modern 16-foot doors better. Choose extension springs only if the header is too low for torsion, and make sure each coil has a safety cable threaded through it.
Spring repair in Boulder City typically runs $180-$340, parts and labor included, whether it’s one torsion spring or a pair of extension springs. The two options land in the same range, so the deciding factor is what your garage can take rather than price. Call (844) 560-4479 for an exact written quote – estimates are free.
Same-day spring repair is often possible when you call in the morning, since our technicians carry both spring types on every appointment. A live person answers the phone 24/7, so you can reach us nights, weekends and holidays to set a real arrival window.
That’s common in Historic District garages, where 7 inches of headroom instead of 10 to 12 leaves no room for a torsion shaft. Extension springs with safety cables are usually the answer, and we’ll confirm it by measuring your header before quoting anything. If you’d rather have it looked at, call (844) 560-4479.
Get a straight answer on your garage
If you’re weighing torsion vs extension springs and you’d rather have someone measure your header than guess from a chart, Bramwell Garage Door Repair Boulder City offers a no-pressure assessment in Boulder City – call (844) 560-4479 for a free estimate. You’ll get a written price for each option before any work starts.
Written by the team at Bramwell Garage Door Repair Boulder City, serving Boulder City, NV.